Skip to content

Most visited

Recently visited

navigation

Regulatory Disclosures for ADT-1

Disclosures for the ADT-1 device.

Model: W2
FCC ID: A4R-W2
IC: 10395A-W2

U.S. Federal Communications Commission Notices

To satisfy FCC and IC exposure requirements, a separation distance of at least 20 cm should be maintained between the antenna of this device and persons during device operation. Operations at closer than this distance are not recommended.

The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by Google Inc. could void the user's authority to operate the equipment.

Industry Canada Notices

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.


CAN ICES-3 (B)/NMB-3(B)

Avis d’Industrie Canada

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

En vertu de la règlementation d’Industrie Canada, cet émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

La puissance rayonnée en sortie de l'appareil sans fil est inférieure aux limites fixées par Industrie Canada en matière d'exposition aux radiofréquences. L'appareil sans fil doit être utilisé de sorte que la possibilité d'un contact humain pendant le fonctionnement normal soit limitée.

This site uses cookies to store your preferences for site-specific language and display options.

Get the latest Android developer news and tips that will help you find success on Google Play.

* Required Fields

Hooray!

Browse this site in ?

You requested a page in , but your language preference for this site is .

Would you like to change your language preference and browse this site in ? If you want to change your language preference later, use the language menu at the bottom of each page.

This class requires API level or higher

This doc is hidden because your selected API level for the documentation is . You can change the documentation API level with the selector above the left navigation.

For more information about specifying the API level your app requires, read Supporting Different Platform Versions.

Take a one-minute survey?
Help us improve Android tools and documentation.